ID |
Name |
Beschreibung |
Bestand |
10001315 |
Infrarot Distanzzsensor |
4-30cm |
5 |
10001316 |
Buck-Converter Module |
In: 4.5-28V, Out: 0.8-20V adjustable
Max: 3A
LM2596 |
0 |
10001317 |
Metallmassstab 15cm |
|
8 |
10001318 |
AP2553AW6-7 |
IC PD SW Current limiter SOT26
Spannungs Limitier IC
Recommended Maximum
Continuous Load Current = 2.1 A
Vin: 2.7-5.5V |
50 |
10001319 |
GAFFA TAPE (258) |
Gaffer Tape Gerband 258 schwarz |
4 |
10001320 |
DUCT TAPE STRONG (250) |
Gerband Duct Tape 250 black |
8 |
10001321 |
DUCT TAPE BILLIG (400) |
Stairville Duct Tape 400 black |
13 |
10001322 |
RTC Modul |
Tiny RTC I2C modules 24C32 memory DS1307 clock RTC module
DS1307 based real time clock module
Two wire I2C interface.
Hour:Minutes : Seconds AM/PM.
Day Month, Date - Year.
1Hz output pin.
56 Bytes of Non-volatile memory available to user.
The DS1307 is accessed via the I2C protocol.
Item size: 28*26*8mm
Net weight: 7g |
10 |
10001323 |
Trinket-Powered NeoPixel Goggle Kit Pack |
One of the most popular Trinket projects now has its own kit pack! Make your very own programmable NeoPixel goggles with 2 x 16 LED rings and an Adafruit Trinket. It even comes with a rechargeable LiPoly battery and charger. It's a great easy build and when you're done you'll have the coolest accessory.
Follow along with our popular Kaleidoscope Eyes tutorial. The pack contains almost everything you need to put a pair of NeoPixel Rings in our costume goggles and power them with an Adafruit Trinket. The LED rings fit perfectly inside 50mm round goggles and we include a 3.7v 150mAh battery and and Micro Lipo charger so you can run the battery and charge it all while contained in the goggles themselves.
These are fairly easy to put together and should take around an hour to make. You'll need some basic soldering and hand tools to install the JST connector on the bottom side of the Trinket and connect your NeoPixel rings. We don't include a soldering iron or solder but sell them in the Adafruit store and you can find epoxy or hot glue at most hardware/craft stores. The soldering is easy and is possible to do by beginners, its a 1-2 hour project (30 minutes if you are a kit-making expert!) Check the tutorial page to see what you'll need to complete the project!
You'll also need a classic USB Micro B cable to program the Trinket, we don't include it as people tend to have too many USB cables in their desk drawer, but if you need one, you can get it from us here.
Please note! They look great, but we don't recommend putting the goggles over your eyes when they're all lit up since the lights can be bright and the goggle lenses can be hard to see out of. However, the goggles work great for costumes/accessories when they're put on top of your forehead! |
1 |
10001324 |
T-Stecker (m-f pair) |
T-connector für batterien udgl. in modellbau, quadrokopter, sonstige drohnen (von ali) |
9 |
10001325 |
USB 3.0 Kabel A<->B Micro |
0.6m A Stecker auf B Micro |
1 |
10001326 |
USB 3.0 Kabel A<->B |
0.6m, A auf B |
1 |
10001327 |
Molex IDE Stromanschluss Y Splitter |
Macht aus einem PC-Internen Stromanschluss zwei. |
10 |
10001328 |
Klinkenstecker 3.5mm Stereo, Kunststoff |
Klinkenbuchse, 3,5mm Stereo, Kunststoffgehäuse, zum Löten |
8 |
10001329 |
USB-C to USB-A Converter |
USB OTG adapter from USB-C to USB-A (e.g. to plug in mice and keyboards into your keyboard |
-3 |
10001330 |
HDMI Kabel 1m |
|
1 |
10001331 |
RTC Modul inkl. Batterie |
DS1307 I2C real-time clock
24C32 32K I2C EEPROM
With CR2032 included |
0 |
10001332 |
RS485 to UART Module |
MAX485, slew-rate limited transceiver, 5V, 44x14mm |
8 |
10001333 |
GPS NEO6MV2 |
GPS Modul, chinois |
3 |
10001334 |
USB 3.0 A zu C |
1m |
-1 |
10001335 |
XLR-Stecker, 3p female |
|
11 |
10001336 |
Arduino-Klon Pro Mini |
|
7 |
10001337 |
GSM Modul |
SIM800L GPRS GSM Module
3.7-4.2V (TTL kompatibel) |
3 |
10001338 |
IR LED |
Infrarot LED 5mm |
101 |
10001339 |
Wannenstecker 26P gewinkel |
|
6 |